SMT placement machine ASM Siemens placement machine TX2i/TX2/TX1

Introduction to ASM Siemens Mounter TX2i: ASM Siemens Mounter TX2i: Provide high performance and high precision in a very small footprint. The ASM Siemens Mounter TX2i mounter module sets a new benchmark for mass production. No other placement solution can achieve 25 µm @ 3 sigma accuracy at speeds up to 96,000 cph in such a small footprint (only 1m x 2.3m).

Enquiry

ASM Siemens TX placement machine, Siemens X series placement machine, ASM Siemens placement machine TX2i technical parameters:

machine characteristics	SIPLACE TX2i	SIPLACE TX2	SIPLACE TX1
Mounting speed (reference speed)	UP TO 96,000 cph	UP TO 85,500 cph	UP TO 44,000 cph
Machine Dimensions (L x W x H)	1.0 x 2.23 x 1.45 m	1.0 x 2.35 x 1.45 m
placement head	SIPLACE SpeedStar (CP20P2), SIPLACE MultiStar (CPP), SIPLACE TwinStar (TH)
Component range	0.12 mm x 0.12 mm to 200** mm x 125 mm
PCB Dimensions (L x W)	50 mm × 45 mm to 550** × 260 mm (double track) 50 mm × 45 mm to 550* × 460 mm (monorail mode)
Feeding method	UP TO 80 × 8 mm tape FEEDER, JEDEC trays, linear dipping unit, Dispensing feeder
耗电量	1.6 KW (Equipped with vacuum pump + frequency converter) 1.2 KW (Without vacuum pump)
耗气量	120 Nl/min (Equipped with vacuum pump)		70 Nl/min (Equipped with vacuum pump)
* Longboard option (non-longboard option, maximum PCB length is 375 mm) ** With restrictions

placement head	SIPLACE SpeedStar (CP20P2)	SIPLACE MultiStar (CPP)	SIPLACE TwinStar (TH)
Component range	0.12 mm x 0.12 mm to 8.2 mm x 8.2 mm	01005 to 50 mm x 40 mm	0201 to 200 mm x 125 mm
Component height	4 mm*	11.5 mm	25 mm
Mounting accuracy (3 σ)	25 µm	34 µm	22 µm
Best Performance (Baseline Speed)	48,000 cph	25,500 cph	5,500 cph
Mounting pressure	0.5 N to 4.5 N	1.0 N to 10 N	1.0 N to 15 N
*2 mm on SIPLACE TX2i

MAECENAS IACULIS

Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.

ADIPISCING CONVALLIS BULUM

Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
Diam parturient dictumst parturient scelerisque nibh lectus.

Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.

Click to enlarge

Back to products

Categories: ASM SIEMENS, SMT placement machine

Description
Shipping & Delivery

Description

machine characteristics	SIPLACE TX2i	SIPLACE TX2	SIPLACE TX1
Mounting speed (reference speed)	UP TO 96,000 cph	UP TO 85,500 cph	UP TO 44,000 cph
Machine Dimensions (L x W x H)	1.0 x 2.23 x 1.45 m	1.0 x 2.35 x 1.45 m
placement head	SIPLACE SpeedStar (CP20P2), SIPLACE MultiStar (CPP), SIPLACE TwinStar (TH)
Component range	0.12 mm x 0.12 mm to 200** mm x 125 mm
PCB Dimensions (L x W)	50 mm × 45 mm to 550** × 260 mm (double track) 50 mm × 45 mm to 550* × 460 mm (monorail mode)
Feeding method	UP TO 80 × 8 mm tape FEEDER, JEDEC trays, linear dipping unit, Dispensing feeder
耗电量	1.6 KW (Equipped with vacuum pump + frequency converter) 1.2 KW (Without vacuum pump)
耗气量	120 Nl/min (Equipped with vacuum pump)		70 Nl/min (Equipped with vacuum pump)
* Longboard option (non-longboard option, maximum PCB length is 375 mm) ** With restrictions

placement head	SIPLACE SpeedStar (CP20P2)	SIPLACE MultiStar (CPP)	SIPLACE TwinStar (TH)
Component range	0.12 mm x 0.12 mm to 8.2 mm x 8.2 mm	01005 to 50 mm x 40 mm	0201 to 200 mm x 125 mm
Component height	4 mm*	11.5 mm	25 mm
Mounting accuracy (3 σ)	25 µm	34 µm	22 µm
Best Performance (Baseline Speed)	48,000 cph	25,500 cph	5,500 cph
Mounting pressure	0.5 N to 4.5 N	1.0 N to 10 N	1.0 N to 15 N
*2 mm on SIPLACE TX2i

Shipping & Delivery

Reviews

There are no reviews yet.

Be the first to review “SMT placement machine ASM Siemens placement machine TX2i/TX2/TX1”

Related products

Yamaha Ultra-High-Speed Modular Z:TA-R YSM40R Mounter placement machine

SMT placement machine, Yamaha

Specifications

		Z:TA-R YSM40R
		4-Beam, 4-Head Spec. (YSM40R-4)
Applicable PCB		L700×W460mm to L50×W50mm
Mounting capability (under optimum conditions as defined by Yamaha Motor)		200,000CPH (When using RS head)
Applicable components	Ultra-High-Speed (RS) Head	0201mm* to □6.5mm (Height 2.0mm or less) *option
Applicable components	Multi (MU) Head	03015mm to 45×60mm (Height 15mm or less)
Mounting accuracy (Under optimum conditions as defined by Yamaha Motor when standard evaluation materials are used)		+/-35μm (25μm) Cpk ≧1.0 (3σ)
Number of component types * 8mm width tape conversion		Max. 80 feeders with RS heads Max. 88 feeders with MU heads Max. 84 feeders with RS x 2 + MU x 2 heads
Power supply		3-Phase AC 200/208/220/240/380/400/416V +/-10%
Air supply source		0.45MPa or more, in clean, dry state
External dimension		L1,000×W2,100×H1,550mm (excluding projections)
Weight		Approx. 2,100 kg

Yamaha Premium Modular Σ-F8S Mounter placement machine

	Σ-F8S
Applicable PCB	Single lane : L330 x W250 to L50 x W50mm (Option : L381 x W510 to L50 x W50mm) Dual lane : L330 x W250 to L50 x W50mm
Head/Applicable components	High-speed head : 0201mm CHIP to 4.3 x 3.4mm, Height 2.0mm or less High-speed multi-purpose head : 03015mm CHIP to 33mm square, Height 12.7mm or less
Mounting capability	High-speed head x 4 specs : 150,000CPH (Dual lane) 136,000CPH (Single lane)
Mounting accuracy (Under optimum conditions as defined by Yamaha Motor when standard evaluation materials are used)	High-speed head : 0201mm/03015mm : ±25μm (3σ) (140,000CPH) 0402mm/0603mm : ±36μm (3σ) (150,000CPH)
Number of component types	Max.80 types (conversion for 8mm tape feeder)
Power supply	3-Phase AC200V ±10% 50/60Hz
Air supply source	0.45 to 0.69MPa (4.6 to 7kgf/cm2)
External dimension	L 1,280 x W 2,240 x H 1,450mm (excluding projections)
Weight	Approx. 1,940kg

Specifications and appearance are subject to change without prior notice.

Panasonic Mounter CM602-L high-speed placement machine

SMT placement machine, Panasonic

Control mode: microcomputer mode External memory: Manage data at PT∗4. Each set of data requires about 1MB. (1 type is required for each 1 type 3.5 2HD floppy disk) Program data: Points Max. 10000 points CM602 power supply Power supply for normal use: 3-phase AC 200 V/ 220 V ±10 V, 3-phase AC 380 V/ 400 V/ 420 V/ 480 V ±20 V Frequency: 50/60 Hz Power supply for HUB ∗ 3: Single-phase AC 100 V ~ AC 240 V Frequency: 50/60 Hz Rated capacity: main machine 4.0 kVA / HUB power supply ∗ 3: 140 VA Supply air pressure: 0.49 MPa ~ 0.78 MPa (operating air pressure is 0.49 MPa ~ 0.54 MPa) Supply air volume: 170 L/min (A.N.R.) Dimensions: 2350 mm (W) × 2690 mm (D) × 1430 mm (H) (excluding 3-section signal tower and color touch panel) quality: Mass of the main engine: 3400 kg (140 kg for the standard configuration without the overall exchange trolley) Overall exchange trolley mass: 140 kg (per 1) Direct tray feeder mass: 195 kg (per 1 unit) Standard composition mass: 3960 kg (1 main engine, 4 overall exchange trolleys) Environmental conditions: Temperature: 10°C ~ 35°C Humidity: 25% RH ~ 75% RH (but water vapor does not condense) Transport and storage conditions: Temperature: −20°C ~ 60°C Humidity: Below 75 % RH (but water vapor does not condense) Altitude: from 0 m above sea level to below 1000 m Noise: < 70dB (A)

High-efficiency Modular Z:LEX YSM20WR Mounter placement machine

Model	YSM20WR
Applicable PCB	Dual lane ^{Note 1} Same type PCBs: L810 x W356 to L50 x W50 Different type PCBs: up to L810 x W662 ^{Note 2} Same type PCB: L810 x W280 to L50 x W500 Different type PCBs: up to L810 x W510
Head / Applicable components	High-Speed Multi (HM) Head ^{Note 3} 0201mm to W55 x L100mm, Height 15mm or less Odd-shaped components (FM: Flexible Multi) head: 03015mm to W55 x L100mm, Height 28mm or less
Mounting capability (under optimum conditions as defined by Yamaha Motor)	X axis 2-beam ^{Note 1}: High-speed multi-purpose (HM: High-speed Multi) head x 2 81,000CPH
Mounting accuracy	±0.035mm (±0.025mm) Cpk≧1.0 (3σ) (under optimum conditions as defined by Yamaha Motor when standard evaluation materials are used)
Number of component Types	Fixed plate: Max. 140 types (conversion for 8mm tape feeder) Feeder carriage exchange: Max. 128 types (conversion for 8mm tape feeder) Trays for 30 types (Fixed type: max., when fitted with sATS30) and 10 types (Carriage type: max., when fitted with cATS10)
Power supply	3-Phase AC 200/208/220/240/380/400/416V +/-10% 50/60Hz
Air supply source	0.45MPa or more, in clean, dry state
External dimension (excluding projections)	L 1,374 x W 2,110 x H1,445mm (Main unit only)
Weight	Approx. 2,500kg (Main unit only)

Note 1 : When using conveyor separation specifications of 787mm between 1 to 4 lanes

Note 2 : When using conveyor separation specifications of 630mm between 1 to 4 lanes

Note 3 : Please contact us for info regarding mounting 0201mm components.

Yamaha Wide-Range Compact Modular YC8 Mounter placement machine

		YC8
Applicable PCB		L50 x W50mm to L330 x W360mm ^*1
Mounting accuracy	When using Yamaha's standard components	Absolute accuracy (μ+3σ):+/-0.05mm /QFP Repeatability(3σ) +/-0.03mm /QFP
Mounting capability	Indication	2.5sec/component (Cycle time from a pickup to mounting with recognition)
Applicable components		4 x 4mm to 100 x 100mm ^*2 (Some components larger than 45 x 45mm ane conditional) Maximum components heights 45mm Maximum payload 1kg
Component supply configuration: Number of component types		Tape reel : MAX. 28 types (8mm width) Tray : MAX. 15 trays Stick
Power supply		3-Phase AC 200/208/220/240/380/400/416V　+/-10%　50/60Hz
Air supply source		0.45MPa or more, in clean, dry states
External dimension (excluding projections)		L 880 x W1,440 x H1,445mm (Main unit only) L 880 x W1,755 x H1,500mm (When ATS15 is installed)
Weight		Approx. 1,000kg (Main unit only) ATS15 : Approx. 120kg

*1: Please consult us separately for maximum board sizes.

*2: Consult us separately regarding component sizes outside the specifications.

Panasonic CM202 placement machine Mounter

Main parameters of CM202 placement machine: 2004 equipment PCB size: 460mm×360mm Component range that can be attached: 0201 to 24mmQFPS Material station: 104 Theoretical placement speed: 0.088s/chip 40909 pieces/hour Mounting accuracy: ±0.05mm Dimensions and Weight: 2,350(L) X 1,950(D) X 1,430(H)mm&2,800kg Power supply and air source: 3P/200V±10V/3KVa

Panasonic Mounter NPM-TT2 multifunctional production system placement machine

The Panasonic Mounter NPM-TT2 is a line configuration capable of achieving both high productivity per unit area and versatility *When directly connecting the NPM-W2, an M-size double-track conveyor belt (optional) is required. The placement head (8-nozzle placement head, 3-nozzle placement head - you can choose the general-purpose 8-nozzle placement head or the 3-nozzle placement head with special-shaped component capability) The specification of the supply part can be selected .change. By reorganizing the tray feeder/exchange trolley, the line configuration can be adapted to the component supply form. Using a multi-functional recognition camera, the recognition and inspection of the height direction of the components can be realized at a high speed, and it can carry out stable and high-speed mounting of special-shaped components) Alternate mounting and independent mounting correspondence ——(can choose the best mounting method corresponding to the production substrate)

Panasonic NPM-W2 Multifunctional Mounter placement machine

Product Features of Panasonic NPM-W2 Multi-Function Mounter 1. Install & inspect a complete system to achieve efficient and high-quality production To match the actual installation requirements, you can choose high-yield or high-precision mode 2. Can correspond to larger substrates and large components Correspondingly, on a large substrate of 750×550 mm, the component range is also expanded to L150×W25×T30mm 3. Double-track installation (select specifications) to achieve high productivity per unit area According to the production substrate, you can choose independent mounting, alternate mounting, mixed mounting and other mounting methods